-
Gel Seal Closure
-
Cold Shrink Tube
-
Tape
-
Cable
-
RF Coaxial Cable Assembly
-
RF Coaxial Connector
-
RF Coax Adapter
-
Lightning Arrester
-
Connector Dust Cap
-
Cable Clamp and Hangers
-
Cable Entry System
-
Grounding Kit
-
Ground Bar
-
Cable Lugs/Terminal
-
Hoisting Grip
-
RF Microwave Devices
-
Other Site Materials
RF Dummy Load / Termination Load
Power(W):2/5/10/25/50/100/200/300W
Frequency(MHz):3G/4G/680-3800MHz
Connector: N/DIN/4.3-10/BNC
HDG Telecom is professional cell site RF components supplier. Termination loads absorb RF & microwave energy and are commonly used as dummy loads of antenna and transmitter. They are also used as match ports in many multiport microwave device such as circulator and directional coupler to make these ports which are not involved in the measurement be terminated in their characteristic impedance in order to ensure an accurate measurement.
Termination loads, also call dummy loads, are the passive 1-port interconnect devices, which provide a resistive power termination to properly terminate the output port of a device or to terminate one end of an RF cable. HDG-Telecom Termination loads are characterized by low VSWR, high power capacity and performance stability. Widely used for DMA/GMS/DCS/UMTS/WIFI/WIMAX etc.

2W N-Male type dummy load
Item No.: DL-2NM-8G
Power: 2W
Impedance:50 ohms
Connector: N-Male
Frequency: DC-8000MHz(0-8GHz)
Material: Stainless Steel

5W 3G N-Male dummy load
Item No.: DL-5NM-3G-110P5
Power: 5W
Impedance: 50 ohms
Connector: N-Male
Frequency: DC-3000MHz(0-3GHz)
Application: IP65, Indoor/outdoor use

10W 50ohm DC-3G dummy load
Item No.: DL-10NM-3G
Power: 10W
Impedance: 50 ohms
Connector: N-Male
Frequency: DC-3000MHz/ 680-3800MHz
VSWR: ≤1.20

25W 800-2100MHz dummy load
Item No.: DL-25NM-800T2100-N
Power: 25W
Impedance: 50 ohms
Connector: N-Male
Frequency: 800-2100MHz
VSWR: ≤1.20

50W RF Microwave termination load
Item No.: DL-50DM-3G-XP5
Power: 50W
Impedance: 50 ohms
Connector: N-Male/ N-Female/ DIN-Male
Frequency: DC-3000MHz (0-3GHz)/ 680-3800MHz
Application: IP65, Indoor/outdoor use

100W rf dummy load with DIN-Male connector
Item No.: DL-100DM-3G-XP5
Power: 100W
Impedance: 50 ohms
Connector: DIN-Male
Frequency: DC-3000MHz(0-3GHz)/ 680-3800MHz
Application: IP65, Indoor/outdoor use

200W DC-5G RF dummy load
Item No.: DL-200DM-3G
Power: 200W
Impedance: 50 ohms
Connector: DIN-Male/ N-Male
Frequency: DC-3000MHz(0-3GHz)/ 680-3800MHz
VSWR: ≤1.20

RF dummy load X-1059 Serise
Item No.: DL-X-1059
Power: 25/ 50/ 100/ 200W
Impedance: 50 ohms
Connector: DIN/ N/ 4.3-10
Frequency: 340-3800MHz
PIM3: ≤-155dBc@2x43dBm
Ingress Protection Class: IP65
What are the functions of RF dummy load?
●When test a radio transmitter, a dummy load acts as protector of the transmitter. The transmitter may result in being damaged if there is no such a dummy load. An antenna is the normal load for the test, while a dummy load is the replacement of the antenna. A dummy load with 50 ohms gives your transmitter the proper resistance, protecting it at its final RF amplifier stage, so it is also called 50 ohm dummy load.
●When test and adjust the transmitter, you may receive other radios signal on your test frequency, which can cause interference. The dummy load is able to avoid RF wave reflections which can cause distortion of information. As a result, you can get correct adjustments.In the same way, you won’t QRM (artificial interference to transmission) others’ transmitter adjustment.
●It is also used as a substitute of the loudspeaker during audio amplifier testing.
Note: Specifications can be changed according with customers' requirements.
Connectors can be N-type, DIN-type, 4.3-10-type and BNC-type.
Power: 2W, 5W, 10W, 25W, 50W, 100W, 200W, 300W.
Frequency: DC-3G, DC-4G, DC-5G.
HDG TELECOM offers: neutral host DAS and co-siting combiner solutions, hybrid couplers and hybrid matrices, attenuators, RF terminations, RF power splitter and diplexers, also known as cross band couplers.
Customized available, contact us now.
Newsletter
Please enter your email address and subscribe to our news alerts.